The European Skull Mount at Home: Boiling, Beetles and Bleaching

Of all the ways to keep a memory of a legally taken animal, the European skull mount is the most honest. Nothing is faked. There is no form, no glass eye, no painted nose, just the clean bone and the antlers or horns as they grew. It is also the one form of taxidermy that a patient person can do well at home with a few tools and a great deal of time. We have done it badly and we have done it well, and the difference lies almost entirely in temperature and in what you use to whiten the bone.

Starting with the skull

Skin the head completely, removing the eyes, the tongue and as much muscle as a knife can reach. Cut away the lower jaw if you do not intend to keep it; most people do not, since the skull sits flat on a plaque without it. Take out the brain as best you can through the opening at the base of the skull, using a bent wire or a strong jet of water from a garden hose. Every ounce of tissue you remove now saves an hour of cleaning later.

If the antlers are still attached, and they always are on a deer skull, wrap them in plastic bags secured with tape below the burr. Hot water and cleaning agents discolor antlers quickly, and a bleached-out antler is the mark of a hurried job.

Simmer, do not boil

The word boiling is used everywhere and it is wrong. A rolling boil cooks the bone, drives grease deep into it, and loosens the sutures between the plates of the skull, sometimes to the point where the nasal bones and the delicate turbinates inside the nose fall apart. What you want is a bare simmer, around 160 to 180 degrees, in a pot large enough to submerge the skull up to the base of the antlers.

Add a generous handful of washing soda, sodium carbonate, which loosens tissue and cuts fat. Simmer for two to three hours, then lift the skull out and pick away everything that has softened with a knife, pliers and a stiff brush. Return it to the pot and repeat. A deer skull usually needs two or three sessions; a bear or an elk needs more. Work outdoors or in a garage with a camp stove, because the smell is sincere and it lingers.

Some people use a pressure washer to blast off remaining tissue after the first simmer. It is fast, but it sends fragments in every direction, so wear eye protection and old clothes.

Dermestid beetles: the professional’s method

Museums and serious skull cleaners do not simmer at all. They keep colonies of dermestid beetles, small brown insects whose larvae eat dried flesh and leave bone untouched. A healthy colony of several thousand beetles cleans a deer skull in three to five days, reaching every crevice inside the nasal cavity without loosening a single suture. The result is a skull with far more fine structure preserved than any pot can manage.

The catch is that a colony is a pet with demands. The beetles need a warm, dark enclosure held around 75 to 80 degrees, a steady supply of skulls or dried meat, and careful separation from your house, because an escaped dermestid population is a genuine hazard to wool, furs and every mount you own. Starter colonies are sold by suppliers for roughly 40 to 100 dollars, and a heated enclosure adds a similar amount. Skulls must be skinned, dried for a day or two, and given to the beetles fresh, never after simmering.

For someone who cleans one skull a year, the beetles are not worth the trouble. For a household of several hunters, they are a wonderful investment.

Degreasing: the step everyone skips

Bone is porous and full of fat, and a skull that looks clean and white when it dries will turn yellow and blotchy over the next year as that grease migrates to the surface. This is the most common failure we see in home skull mounts, and it is entirely avoidable. Degreasing means soaking the cleaned skull in warm water with dish soap or ammonia for days or weeks, changing the water whenever it turns cloudy.

A whitetail takes a week or two in a soapy bath held at around 100 to 115 degrees, which an aquarium heater in a plastic tub manages nicely. Bears, boars and old bucks can take a month or longer. You are done when the water stays clear and the bone, once dry, shows no translucent or yellowish patches, particularly around the nose and the back of the skull.

Whiten with peroxide, never with bleach

Household chlorine bleach is the ruin of more skulls than any other single mistake. It attacks the structure of the bone, leaves it chalky and prone to crumbling, and continues to work long after the skull is dry. Do not use it, even diluted.

Hydrogen peroxide is what you want. The 3 percent solution sold in drugstores works, but slowly; a soak of two or three days in a covered container gives a clean, natural white. Salon-grade developer at 12 percent, sold as 40 volume cream, is faster and can be painted onto the skull with a brush, then wrapped in plastic for a day. Wear gloves and keep it off the antlers. Rinse thoroughly and let the skull dry in the shade for a few days. The goal is a soft ivory, not the dead blue-white of a bathroom tile.

Plaques, hangers and what it all costs

A finished skull can hang from a simple screw eye set into the back, or it can be mounted on a plaque with a small bracket that holds it at an angle. Walnut and oak plaques cost 15 to 40 dollars; a hanging bracket adds ten or so. Some people seal the skull with a matte clear spray, which helps keep dust from settling into the pores, though many prefer bare bone.

Put the whole project together and a home European mount costs 20 to 60 dollars in supplies and perhaps ten to fifteen hours of work spread over a month, most of it waiting. A studio charges 100 to 250 dollars for the same result on a deer, more for bear, elk or a boar with tusks, and the professional version will almost always be cleaner. Either way, the skull is a quiet and dignified way to remember the animal, and to keep learning from its anatomy every time you pass it on the wall.